Allied StormShield: Engineered Class 4 Impact-Resistant Roofing Systems Built for Illinois Storms

Allied StormShield is a three-tier roofing system engineered specifically for Illinois hail, wind, and roof-age underwriting pressures. Every tier centers on UL 2218 Class 4 impact-resistant shingles, manufacturer-specified high-wind nailing, and full code compliance with the International Residential Code chapters governing roof assemblies (IRC R905), attic ventilation (R806), and roof sheathing (R503). The tiers differ in deck construction, edge metal, gutter performance, and FORTIFIED Roof compliance. All three tiers are installed by an Illinois-licensed roofing contractor (License #104.019029) under municipal building permit. Allied StormShield is not a product line we resell; it is a construction specification we engineered from first principles based on what we have seen fail — and what we have seen survive — across more than two decades of Illinois storm restoration work.

---

Why a Standardized Roofing System Matters

Most Illinois roof replacements are quoted as line items: tear-off, underlayment, shingles, drip edge, ventilation, gutters. The line items vary contractor-to-contractor. The specifications vary contractor-to-contractor. The result is that two homeowners on the same block can get “new roofs” that perform very differently in the next storm — and that an insurance underwriter cannot meaningfully compare.

Allied StormShield is an answer to that variability. Each tier is a fixed engineering specification with documented material standards, manufacturer-required installation methods, and a complete documentation packet that an underwriter, a future buyer’s home inspector, or a manufacturer warranty department can verify independently.

We built StormShield because we have watched too many roofs fail prematurely from buildable defects: deck sheathing left in place that should have been replaced, underlayment installed mechanically when the wall section needed self-adhered ice barrier, three or four nails per shingle when six were required for the manufacturer’s published wind warranty, drip edge omitted entirely, ridge vents that the wind tore off because their fastener pattern was wrong. Each of those defects is a code violation, a warranty void, or both. StormShield exists to make those defects impossible to introduce on an Allied installation.

---

What Makes Allied Qualified to Build It

Allied Emergency Services has held an active Illinois Roofing Contractor License (#104.019029) since the company’s founding and has installed roofing systems across the state’s primary hail corridor — DuPage, Lake, McHenry, Cook, Will, Kane, Winnebago, Sangamon, and McLean counties — under municipal building permit for every project. Our credentials in the four areas that determine a roof’s real-world performance:

• Code mastery. We work in the International Residential Code daily. Chapter R9 (Roof Assemblies), Chapter R8 (Roof-Ceiling Construction), Chapter R5 (Floors and Sheathing), and the wind-load provisions of R301 are the daily reference. Illinois adopts the IRC with limited state amendments, and most Illinois municipalities adopt the IRC directly or by reference. We know which sections apply, which require local interpretation, and where the most common compliance failures occur.
• Storm restoration experience. Allied has worked through every major Illinois hail and wind event of the past two decades, including the 2015 Coal City tornado, the 2020 derecho, the 2023 Rolling Fork-pattern storms across central Illinois, the 2024-2026 tornado outbreaks across Kankakee, Will, and DuPage counties, and the recurring spring hail events across the I-39 and I-55 corridors. We have inspected, scoped, and rebuilt thousands of storm-damaged roofs, which means we have seen the specific construction details that survive and the ones that fail.
• Manufacturer credentialing. Allied is qualified to register the enhanced (transferable) manufacturer warranties offered by Atlas Roofing Corporation and GAF, the two manufacturers we specify for StormShield. These enhanced warranties are not available to homeowners who hire unaffiliated contractors.
• Documentation discipline. Every Allied installation produces a documented evidence chain — manufacturer certification letter, product specification sheets, contractor invoice, permit and inspection records, warranty registration certificate, and installation photographs. This packet is the basis for both manufacturer warranty claims and homeowner insurance-carrier mitigation credit submissions.

Beyond the Illinois roofing license, Allied holds Wisconsin Dwelling Contractor Qualifier credential #DCQ-092100962, EPA Lead-Safe Certified Firm status (#NAT-F303832-1), IICRC Certified Restoration Firm status (#70133670), OSHA 30-Hour Construction Safety certification, FEMA emergency response certifications (ICS-100, ICS-200, IS-700, IS-800, IS-2900), and Vinyl Siding Institute Certified Installer credential #28216. These are not marketing badges. They are the credential set required to build a roofing system, manage a job site safely, and document the work to a standard that satisfies both manufacturer warranty registrars and insurance carrier underwriters.

---

The Three Tiers at a Glance

Specification	StormShield Standard	StormShield Premium	StormShield FORTIFIED
Shingle	Class 4 IR (UL 2218)	Class 4 IR (UL 2218)	Class 4 IR (UL 2218) + FORTIFIED-rated
Deck retention	Existing deck retained, inspected, re-nailed	Full structural redeck, 5/8″ CDX, H-clips	Full structural redeck, 5/8″ CDX, H-clips, taped seams
Underlayment	Synthetic field + ice barrier at eaves	Sealed deck: full ice barrier coverage at eaves and valleys + synthetic field	Sealed deck: fully adhered membrane, all seams taped (FORTIFIED standard)
Drip edge	Style-D aluminum, eaves and rakes	Style-D aluminum, eaves and rakes	Enhanced edge metal per FORTIFIED
Nailing pattern	Manufacturer 6-nail high wind	Manufacturer 6-nail high wind	Manufacturer 6-nail high wind, ring-shank
Ridge ventilation	Standard shingle-over ridge vent	Atlas HighPoint or equivalent shingle-over ridge vent	Locked-down ridge vent (FORTIFIED)
Gutter system	Existing gutters retained or replaced 5″ K-style	New 6″ K-style seamless + 3×4 oversized downspouts + leaf guard	New 6″ K-style seamless + 3×4 oversized + leaf guard + properly attached per FORTIFIED
Manufacturer warranty	Registered standard mfr warranty	Registered enhanced mfr system warranty	Registered enhanced mfr system warranty
Workmanship warranty	10-year Allied workmanship	10-year Allied workmanship	10-year Allied workmanship
FORTIFIED designation	Not applicable	Not applicable	Independent IBHS evaluator certification (coordinated by Allied)
Typical investment range (26 sq Illinois roof, 2026)	$14,000–$22,000	$18,000–$30,000	$22,000–$38,000+

The price ranges above are typical for a 26-square (approximately 2,600 square foot) Illinois roof in 2026. Every property is different. Your specific quote depends on roof pitch, complexity, current deck condition discovered at tear-off, municipal permit fees, ventilation upgrades, and any siding, gutter, or fascia work bundled with the project.

---

Allied StormShield Standard: The Entry Tier

StormShield Standard is the right specification for homeowners who need an immediate, code-compliant Class 4 impact-resistant roof but whose existing roof deck is structurally sound and recently sheathed (post-2000 construction, generally) and whose budget needs to stay closer to standard-shingle pricing.

Included:

• Complete tear-off and disposal of the existing roofing system, including shingles, underlayment, and flashing.
• Inspection of existing roof deck. Loose sheathing re-nailed per current code. Deteriorated sections selectively replaced.
• Atlas WeatherMaster 200 self-adhered ice and water barrier at all eaves to the IRC R905.1.2 Climate Zone 5 minimum (24 inches inside the warm wall).
• Synthetic underlayment over the remaining roof deck with cap fasteners per manufacturer specification.
• Style-D aluminum drip edge at all eaves and rakes per IRC R905.2.8.5.
• UL 2218 Class 4 impact-resistant shingles — Atlas StormMaster Shake or GAF Timberline AS II — installed with the manufacturer-specified 6-nail high-wind nailing pattern. The 6-nail pattern is what unlocks the manufacturer’s published 130 MPH wind warranty figure; the default 4-nail pattern qualifies for the standard wind warranty only.
• Manufacturer-matched starter strip and hip and ridge cap.
• Standard shingle-over ridge ventilation, balanced with existing soffit intake.
• New lead pipe boots at plumbing penetrations and new exhaust caps at bathroom and kitchen exhaust terminations.
• Final magnetic nail sweep, full debris disposal, municipal building permit, final inspection.
• Manufacturer warranty registration in the homeowner’s name.
• Ten-year Allied workmanship warranty.
• Complete documentation packet for homeowner insurance carrier mitigation credit submission, where applicable.

When Standard is the right tier: newer homes (post-2000) with sound original sheathing, homeowners replacing an aged roof who do not need the additional engineering of a sealed deck, or homeowners who specifically need the Class 4 IR designation to qualify for a voluntary insurance carrier mitigation credit and who already have adequate underlying construction.

---

Allied StormShield Premium: The Engineered System Tier

StormShield Premium is the tier most homeowners select when they understand what they are buying. It is the specification we install on our own homes and recommend to family. It addresses the failure modes that we have spent two decades documenting on storm-damaged Illinois roofs.

Included (in addition to everything in Standard):

• Full structural redeck. The existing roof deck is removed in its entirety and replaced with 5/8″ CDX plywood (APA-rated, exposure 1), installed over the existing trusses or rafters. This is the upgrade that older Illinois homes most need — pre-2000 construction frequently has 3/8″ or 1/2″ sheathing that the modern APA specifications consider inadequate for current uplift loads.
• MiTek G90 galvanized H-clips installed at all unsupported panel edges per APA E30 and IRC R503 guidance. The H-clip is the small piece of hardware that prevents adjacent sheathing panels from deflecting differentially under uplift loads. Most non-engineered roofs lack them.
• Sealed-deck construction. Self-adhered ice and water barrier coverage extended significantly beyond the IRC minimum — two courses at all eaves to clear the interior warm wall, and 36-inch-centered coverage at all valleys (per IRC R905.1.2 in Climate Zone 5). The remainder of the deck is covered with synthetic underlayment installed with cap fasteners. The result is a roof deck that does not leak even if shingles are removed in a severe wind event.
• Atlas WeatherMaster 200 (or equivalent peel-and-stick equivalent product) as the ice barrier material. Material specification matters: not all self-adhered membranes meet the same temperature-extreme performance window.
• Upgraded shingle specification. Atlas StormMaster Shake or GAF Timberline AS II + Solaris paired with manufacturer-matched hip and ridge cap, starter strip, and high-temperature ridge vent.
• Atlas HighPoint Invisaridge or equivalent shingle-over ridge vent system with manufacturer-specified fastener pattern at all ventable ridges, balanced to soffit intake per IRC R806.
• Hail-resistant gutter system. Complete removal of existing 5-inch gutters; new 6-inch K-style seamless aluminum gutters at all eaves with 3-by-4-inch oversized downspouts (hail-resistant), aluminum hidden hangers at 24 inches on center, full-perimeter gutter screen / leaf-guard system. The 6-inch K-style + 3×4 downspout combination is the gutter geometry that handles storm-event flow rates without overflowing and resists hail damage to a degree that 5-inch K-style with 2×3 downspouts cannot.
• Subfascia inspection. Rotted sections cut out and replaced with new pressure-treated lumber. Fascia boards re-wrapped with aluminum coil stock for a sealed, low-maintenance perimeter. Fascia condition is the single most-overlooked failure point on Illinois roofs — water that gets past a poorly-installed drip edge rots subfascia, which propagates rot into the rake and eventually into the deck itself.
• Registered enhanced (transferable) manufacturer system warranty. Transferable once to a subsequent property owner within the first 10 years of installation.

When Premium is the right tier: older Illinois homes (pre-2000 construction) where the existing deck is not engineered to current standards, homes that have suffered prior leak damage, homes where the homeowner wants to maximize both insurability and resale value, and homes where the next storm event is essentially a question of when rather than if.

---

Allied StormShield FORTIFIED: The Highest-Documented Tier

StormShield FORTIFIED is the specification for homeowners who want the most rigorously documented mitigation status available to American property owners. The roofing system is built to meet the construction requirements published by the Insurance Institute for Business and Home Safety (IBHS) under its FORTIFIED Roof standard.

Important distinction. The FORTIFIED Roof designation is awarded by IBHS through an independent evaluator inspection — not by the contractor who builds the roof. Allied builds the construction to the FORTIFIED standard; the designation itself is issued by an independent IBHS-affiliated evaluator who verifies the construction at completion. Allied coordinates the evaluator visit as part of the project. We are transparent about this division of responsibility because it is the basis of the designation’s value: a third-party verified construction status that travels with the property.

Included (in addition to everything in Premium):

• Sealed roof deck to FORTIFIED specification. Beyond Premium’s self-adhered ice barrier at eaves and valleys, FORTIFIED requires that all sheathing panel seams be either taped or fully covered with a self-adhered membrane. The result is a roof deck that, in the event of total shingle loss, behaves as a continuous water-resistant surface.
• Enhanced edge metal. FORTIFIED specifies higher-gauge drip edge installed with closer fastener spacing than IRC minimum. This is the perimeter detail that, more than any single factor, determines whether wind can lift the roof covering away from the deck at the edge.
• Ring-shank nail fastening pattern. Smooth-shank nails meet IRC code. Ring-shank nails meet FORTIFIED. The pull-out resistance of a ring-shank nail under cyclic wind loading is materially higher.
• Locked-down ridge vent. FORTIFIED requires that the ridge vent be a manufactured product attached with a fastener pattern that has been wind-tunnel tested to remain in place under hurricane-force loading. We specify ridge vents that carry independent test reports documenting performance to that standard.
• Properly attached gutter system per FORTIFIED. Beyond Premium’s 6-inch K-style + 3×4 downspouts, FORTIFIED requires specific gutter-to-fascia attachment and downspout discharge management.
• Coordination of the independent IBHS evaluator visit. Allied schedules the evaluator inspection, prepares the documentation packet, and remains on site to address any items the evaluator identifies.
• Issuance of the IBHS FORTIFIED Roof designation certificate by the evaluator upon successful inspection. The designation is recorded against the property and is transferable with the property at sale.

When FORTIFIED is the right tier: homeowners building or buying long-term residences, properties in particularly hail- or wind-exposed locations (the I-39 and I-55 corridors, properties east of the Mississippi flyway, properties at higher elevation), homeowners selling within the next several years who want a documented resilience asset on the property listing, and homeowners whose insurance carrier has tightened roof-age underwriting and who want the most defensible documentation possible at the next renewal.

---

What Every Allied StormShield Project Includes Regardless of Tier

Some elements are constant across all three tiers because they are not upgrades — they are the minimum acceptable practice for any Allied installation.

Building permit and final inspection. Every Allied StormShield project is installed under a municipal building permit pulled by Allied. The final building inspection is performed by the municipality. Permit-pulling is the contractor’s responsibility, not the homeowner’s, and the permit record is the homeowner’s documentation that the work was performed under code-enforcement oversight. Skipping the permit is a common cost-cutting tactic among unlicensed contractors that we never engage in.

Manufacturer warranty registration. Allied registers the manufacturer warranty in the homeowner’s name within 30 days of substantial completion. Manufacturers issue the warranty certificate directly to the homeowner. This step is what makes the warranty enforceable — an installed roof without registered warranty has only the contractor’s word that the manufacturer will honor the materials claim.

Documentation packet for insurance carrier submission. Every Allied StormShield project produces a complete documentation packet that includes the manufacturer certification letter for the specific Class 4 IR shingle installed, the product specification sheets, the contractor’s final invoice, the municipal permit and final inspection records, the manufacturer warranty registration certificate, and installation photographs. This packet is delivered to the homeowner and is the basis for submitting a wind/hail mitigation credit request to the homeowner’s insurance carrier, where applicable. Allied does not negotiate, broker, or guarantee any insurance credit on the homeowner’s behalf. The credit, if any, originates from the carrier in response to the homeowner’s submission to their licensed insurance agent. The documentation packet ensures the submission can actually be made — most underwriters require exactly the items we include.

Compliance with Illinois consumer protection statutes. Every Allied contract complies with the Illinois Roofing Industry Licensing Act (225 ILCS 335), the Illinois Home Repair and Remodeling Act (815 ILCS 513), and the Illinois Consumer Fraud Act (815 ILCS 505). Our written contract includes the consumer-rights disclosures, contractor identification, work specifications, and payment-schedule terms that Illinois statute requires.

Lead-safe work practices. For any Illinois home built before 1978, Allied applies EPA Lead-Safe Renovation, Repair, and Painting (RRP) practices. Allied is an EPA Lead-Safe Certified Firm (#NAT-F303832-1). This is a federal compliance requirement, not an optional add-on, and most of the cost-cutting roofing contractors in the Illinois market are not RRP-certified.

OSHA-compliant fall protection. Every Allied roofing crew works under OSHA fall protection compliance. Personal fall arrest systems, edge protection, and tie-off points are non-negotiable. Roofing remains one of the most dangerous occupations in the United States; the contractors who skip fall protection are saving money at their workers’ direct expense.

---

How to Choose the Right StormShield Tier

The right tier for any individual Illinois homeowner is determined by a small set of factors. The decision tree we use during the in-home assessment is:

Question 1: How old is the current roof, and what is the underlying deck construction? If the home was built after 2000, the existing deck is likely adequate and Standard may be the right tier. If the home was built between 1970 and 2000, the deck is likely 1/2″ sheathing with no H-clips, and Premium is almost certainly the right tier. If the home is pre-1970 or has any history of leak damage, Premium or FORTIFIED is the right tier.

Question 2: How long does the homeowner plan to stay in the home? If the answer is fewer than 5 years, Standard or Premium is appropriate depending on resale market. If the answer is 10 years or longer, Premium or FORTIFIED is the right tier because the durability premium pays back over the holding period.

Question 3: What is the homeowner’s insurance carrier doing? If the carrier has issued a roof-age notice, sent a non-renewal letter, or moved coverage to actual cash value (ACV), the homeowner needs a documented installation immediately and Premium with documentation packet is the standard recommendation. If the carrier is offering substantial wind/hail mitigation credits, the homeowner should compare the credit value over the holding period against the tier upgrade cost.

Question 4: What is the property’s wind and hail exposure? Properties in the I-39 and I-55 corridors, properties on elevated terrain, and properties east of the Mississippi flyway have higher hail exposure. Properties in tornado-corridor counties (Will, Kankakee, McLean, Macon, Sangamon, DuPage during certain pattern years) have higher wind exposure. Higher exposure justifies higher tier.

Question 5: Does the homeowner intend to sell within a 5-10 year window? FORTIFIED designation is a documented resilience asset on a property listing. The designation is increasingly cited in real estate marketing in markets where insurance availability is a homebuyer concern.

Allied does not push higher tiers. We recommend the tier that the property and the homeowner’s situation justify. A Standard installation on a 2010 home with a sound deck is the right answer for that home. A FORTIFIED installation on a 1962 ranch with original sheathing is the right answer for that home.

---

Frequently Asked Questions

Is Allied StormShield a product or a service?

Allied StormShield is a roofing construction specification. It defines a fixed set of materials, installation methods, manufacturer-specified procedures, and documentation deliverables across three tiers. It is not a third-party-manufactured product. Allied is the installer; the materials are sourced from Atlas Roofing Corporation, GAF, CertainTeed, MiTek, and other named manufacturers.

What manufacturer shingles does Allied use in StormShield installations?

Allied specifies UL 2218 Class 4 impact-resistant shingles from Atlas Roofing Corporation (StormMaster Shake) or GAF (Timberline AS II) as primary options. Other Class 4 IR products from CertainTeed (NorthGate ClimateFlex), Owens Corning (Duration Storm), and Malarkey (Vista, Legacy) are available on homeowner request. The Atlas and GAF lines are our primary recommendation because we hold the enhanced warranty registration credentials with both manufacturers.

How does Allied StormShield differ from a “standard” Illinois roof replacement?

A standard Illinois roof replacement is generally a tear-off, new underlayment, new architectural shingles, and a manufacturer’s standard wind warranty. Allied StormShield replaces every layer of that sequence with an engineered specification: Class 4 IR shingles instead of standard architectural, a manufacturer-published 130 MPH wind warranty via the 6-nail nailing pattern instead of the default 4-nail pattern, sealed-deck construction at Premium and FORTIFIED tiers, structural deck replacement at Premium and FORTIFIED, hail-resistant gutters, and a documentation packet sized to support insurance carrier mitigation credit submission and manufacturer warranty enforcement.

Will Allied StormShield reduce my homeowner insurance premium?

It may qualify for a voluntary wind/hail mitigation credit with most major Illinois carriers — State Farm, Travelers, USAA, Allstate, American Family, Farmers, Erie, and Country Financial all maintain credit programs in Illinois. The credit amount varies by carrier, policy form, ZIP code, and underwriting cycle, and is not guaranteed. Allied does not negotiate, broker, secure, or guarantee any insurance discount on the homeowner’s behalf. The credit, if any, originates from the carrier in response to the homeowner’s documentation submission to their licensed insurance agent. See our Class 4 Impact-Resistant Roofing in Illinois guide for the complete carrier list and submission packet requirements.

Why does Allied not just install standard architectural shingles?

Standard architectural shingles fail at a documented rate in Illinois hail events of 1.5 inches and larger. We have inspected too many of them. The 10% to 20% material-cost premium for Class 4 IR shingles is paid back the first time the homeowner avoids a deductible-eating hail claim and again at insurance renewal time when the mitigation credit is applied. We install architectural shingles only when a homeowner specifically requests them after declining the Class 4 IR upgrade in writing.

How long does an Allied StormShield installation take?

A typical Standard or Premium installation on a 26-square Illinois roof is completed in two to four working days, weather-dependent. FORTIFIED installations may take an additional one to two days because of the additional taping, fastener-pattern verification, and evaluator inspection coordination. Tear-off, deck inspection, deck replacement (Premium and FORTIFIED), underlayment, shingle installation, and gutter installation are sequenced to keep the roof weather-tight at end of each workday.

Does Allied StormShield work on homes outside the Chicagoland area?

Allied serves the greater Chicagoland and central Illinois markets from our Springfield office. We routinely work in DuPage, Lake, McHenry, Cook, Will, Kane, Winnebago, Sangamon, McLean, and surrounding counties. We are also licensed in Wisconsin (Dwelling Contractor Qualifier #DCQ-092100962) and serve southern Wisconsin properties on case-by-case basis. Contact our office to confirm service coverage for a specific property address.

What happens if my deck is worse than expected when you tear off the existing roof?

The Premium and FORTIFIED tiers already include full deck replacement, so unexpected deck damage is absorbed within the original quote. The Standard tier quote assumes the existing deck is structurally sound; if tear-off reveals significant deterioration, Allied will document the condition with photographs, present the homeowner with a written change order before any additional work begins, and offer the homeowner the option to upgrade to Premium or to authorize selective deck replacement at standard material and labor rates. We do not perform additional work without written authorization.

Can the FORTIFIED designation be added to a Standard or Premium installation later?

In principle, yes — but practically, no. The FORTIFIED Roof standard requires construction details (taped deck seams, ring-shank nailing, enhanced edge metal) that are buried under the finished roofing system. Adding FORTIFIED retroactively requires substantially re-doing the installation. The right time to choose FORTIFIED is before the original installation. If you anticipate wanting FORTIFIED designation in the future, choose the FORTIFIED tier at the original installation.

---

What Happens After Installation

Allied StormShield does not end at substantial completion. Every project includes:

• Manufacturer warranty certificate delivered to the homeowner within 30 days of completion, registered in the homeowner’s name.
• Ten-year Allied workmanship warranty documented in writing and signed by Curtis Testa as Owner.
• Documentation packet in either physical or digital format, including manufacturer certification letter, product specification sheets, final invoice, building permit, final inspection record, warranty registration certificate, and installation photographs.
• Insurance carrier submission support. While Allied does not negotiate with carriers on the homeowner’s behalf, we will provide the documentation packet to the homeowner in the format that their carrier prefers and will answer technical questions from the carrier’s underwriter directly if requested by the homeowner in writing.
• Annual roof condition courtesy check offered to StormShield Premium and FORTIFIED customers at no charge for the first five years following installation. The check identifies any developing issues (caulk failure at penetrations, gutter alignment issues, fascia caulk lines) before they become problems.

---

Ready to Discuss an Allied StormShield Installation

If you are considering a roof replacement in Illinois — whether triggered by storm damage, an insurance carrier roof-age notice, a planned home sale, or simply the end of the existing roof’s service life — Allied Emergency Services would welcome the opportunity to evaluate your current roof, document the conditions, and provide a written StormShield tier recommendation with itemized pricing.

Contact our office at (800) 792-0212 or info@alliedemergencyservices.com. The initial evaluation is provided at no cost and includes a written condition assessment that you may use regardless of whether you elect to proceed with Allied. Allied is licensed by the Illinois Department of Financial and Professional Regulation (License #104.019029) and serves the greater Chicagoland and central Illinois markets from our Springfield office.

---

About the Author

Curtis Testa is the Owner of Allied Emergency Services, Inc., an Illinois-licensed roofing and storm restoration contractor (License #104.019029). Curtis personally designed the Allied StormShield specification based on more than two decades of Illinois storm-restoration field experience. He holds Wisconsin Dwelling Contractor Qualifier #DCQ-092100962, IICRC Certified Restoration Firm status (#70133670), EPA Lead-Safe Certified Firm credentials (#NAT-F303832-1), EPA/HUD/IL RRP Lead Renovator certification #R-I-T210065-25-02292, OSHA 30-Hour Construction Safety certification, HAZWOPER 40-Hour certification, Vinyl Siding Institute Certified Installer credential #28216, and FEMA Emergency Response certifications (ICS-100, ICS-200, IS-700, IS-800, IS-2900).

Allied Emergency Services, Inc.
2501 Chatham Rd, Ste 8068
Springfield, IL 62704
(800) 792-0212
info@alliedemergencyservices.com
www.alliedemergencyservices.com

---

Important Disclosures

Allied StormShield is a roofing construction specification offered by Allied Emergency Services, Inc. The specification details, tier definitions, materials, and pricing ranges referenced in this article reflect current Allied practice as of May 2026 and are subject to change. Final scope, materials, and pricing for any specific property are confirmed in a written contract executed between Allied Emergency Services, Inc. and the homeowner.

The “IBHS FORTIFIED Roof” designation referenced in this article is administered by the Insurance Institute for Business and Home Safety (IBHS), a separate organization. IBHS FORTIFIED designation is issued by independent IBHS-affiliated evaluators upon successful inspection. Allied Emergency Services, Inc. constructs roofs to meet the FORTIFIED Roof construction standard and coordinates the independent evaluator visit; Allied does not itself issue the FORTIFIED designation.

Insurance discounts, credits, and underwriting practices vary by carrier, policy form, ZIP code, and underwriting cycle, and may change at any time. Allied Emergency Services, Inc. does not negotiate, broker, secure, or guarantee any insurance premium credit, discount, or coverage outcome on behalf of any homeowner. All premium-credit decisions originate from the carrier in response to the homeowner’s submission to their licensed insurance agent. Homeowners should verify current discount availability and amount directly with their carrier in writing before relying on any specific figure cited in this article. Allied Emergency Services is a licensed roofing contractor, not an insurance company, insurance agent, or public adjuster. Nothing in this article constitutes insurance advice, legal advice, or a guarantee of any premium reduction or coverage outcome.

This article is informational and reflects publicly available industry standards as of May 2026.